Loading..

Product was successfully added to your shopping cart.

Go to cart page

You have successfully subscribed to this product. You will receive an email when the product is in stock.

Menu

Velleman K8203: 0.35mm Extruder Upgrade Kit for K8200 3D Printer

5
Velleman K8203
$129.99
OR

Extruder Upgrade Kit for K8200 3D Printer - For use with 1.75mm PLA or ABS filament

Improve the quality of your 3D prints with the Velleman K8203, a direct drive extruder add-on/replacement for the Velleman K8200: 3D Printer Kit. The K8203 extrusion upgrade kit replaces the standard 0.5mm nozzle with a 0.35mm nozzle, which allows for 1.75mm PLA or ABS filament prints versus the standard 3.00mm filament prints. The upgrade doubles the resolution of your prints from 200 microns (0.2mm) to 100 microns (0.1mm), the same resolution as our K8400 3D Printer Kit.

Simply remove the existing extruder, replace it with the K8203 Direct Drive Extruder and watch as your K8200 3D Printer produces some of your smoothest prints yet.

Please note: To benefit fully from the K8203 upgrade, it is recommended that the Z axis is also upgraded using the Velleman K8204: Z Axis Upgrade for K8200 3D Printer.

Features

  • Print with 1.75mm PLA or ABS filament on your Velleman K8200: 3D Printer
  • Higher resolution 3D prints

Extrusion Upgrade Kit Includes:

  • 0.35mm extruder nozzle for 1.75mm filament
  • Extruder heater and sensor
  • Direct drive unit with stainless steel pulley
  • High power plug-in stepper driver
  • All necessary installation hardware

Upgrade your K8200's extruder in 4 easy steps

Specifications

Extrusion Nozzle Diameter 0.35mm
Filament Diameter 1.75mm. Open filament policy.
Prints PLA and ABS. Testing with other materials in progress.

Additional Information

Difficulty Level 5

Download

FIRMWARE K8200 V2.2
This version supports the K8203 DIRECT DRIVE EXTRUDER and the VM8201 LCD and SD card controller. DO NOT FORGET TO RESET YOUR EEPROM SETTINGS AFTER THE UPGRADE!. Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm.

FIRMWARE K8200 V2.3
This version supports the K8203 DIRECT DRIVE EXTRUDER and the K8204 Z AXIS UPGRADE ROD AND COUPLER FOR K8200 and the VM8201 LCD and SD card controller. DO NOT FORGET TO RESET YOUR EEPROM SETTINGS AFTER THE UPGRADE! (C)2011 C. Gubbels E. van der Zalm

K8203-PLA-STANDARD.INI
Slic3r configuration file for standard PLA prints. Consult the K8200 manual on how to use this file. This file is only compatible with Repetier 0.90 and Slic3r 0.9.10b.

Info Sheets

Infosheet
Resistor colour code

Datasheet
Product information

Overview of Velleman modules that are equal to D.I.Y Kits
This sheet is useful when you want to know which modules you could find in the do-it-yourself range of Velleman Kits and minikits.

 Warning: this product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to: www.P65Warnings.ca.gov/product

Velleman has over 40 years of experience in developing electronics and offers a wide variety of products. With our own research and development department and experienced production team that designs in-house, we bring quality products to electronic enthusiasts. We are a leader in providing DIY electronics kits and components as well as in 3D printers. Whether you are just beginning your exploration of the electronics world or you are an old pro, we have the components you need to create without limits.

 


Info

resources

All registered trademarks and trade names are properties of their respective owners and are used only for the clarification of the compatibility of our products with the products of the different manufacturers. Due to constant product improvements the actual product appearance might differ from the shown images. Product images are for illustrative purposes only.
Top